Step 1

Drain the System

Initially, shut off the supply of water at the main water-supply shutoff. Next, from the most affordable point in the house, open a faucet to launch pressure and drain the majority of the water from the system.
Step 2
Cut the Pipe

Once you’ve selected the area for your filter, use the design template offered with the kit to mark the pipe for precise positioning. Remember that you’ll have to change the cartridge occasionally, and select a place with sufficient clearance beneath the filter tank to enable simple removal and reattachment.

Make use of a pipe cutter to make 2 cuts, and get rid of the marked area of pipeline. Make use of the twist deal with to tighten the cutter onto the pipeline so the blade associate your mark, then rotate the cutter around the pipe as you continue twisting the handle. Keep turning the cutter around the pipe till it cuts all the method through. This might take a minute approximately. (Have a bucket useful to catch any excess water when the pipeline is cut– especially if you’re standing directly underneath.) As soon as you’ve eliminated the area, use the reamer blade on the cutter to get rid of any burrs from inside the newly cut pipeline.
Step 3

Thread a brass fitting onto the “”in”and the “”out”ports of the filter housing. Install them according to the manufacturer’s recommendations.
Connect the Fittings

Location a compression nut, little end initially, on one of the cut pipe ends. Move on the ferrule. Repeat the exact same steps on the other side.

Thread a brass fitting onto the “in” and the “out” ports of the filter housing. Install them according to the producer’s suggestions. Usage Teflon tape to guarantee a good seal between the fitting and the filter port. Tighten up the fittings onto the filter till they’re tight, however don’t over-tighten.

How to Install a Whole-House Water Filter

How to Install a Whole-House Water Filter

Step 4

Hand tighten the compression nuts onto the fitting bodies. Keeping the filter straight and upright, tighten the fittings, using two wrenches.

Hand tighten the compression nuts onto the fitting bodies. Keeping the filter straight and upright, tighten up the fittings, using 2 wrenches.
Position the Filter

Vital: Install the filter so the circulation of water goes into the “in” port and exits through the “out” port. The filter will not work properly if set up backward. (The “in” port must be on the end better to the water meter; the “out” must point toward the water heater.).

Position the filter on the water line, and let it hang temporarily in between the two ferrules.

Hand tighten up the compression nuts onto the fitting bodies. Keeping the filter straight and upright, tighten up the fittings, making use of two wrenches.

Step 5.
Switch on the Water.

The filter kit includes an unique deal with utilized to turn the inlet valve on the top to numerous positions– “off,” “bypass” and “filter.” With the filter appropriately set up, turn the valve to the “off” position. Slowly turn the water back on at the major shutoff valve, and inspect the filter for leaks.

Utilize the manage to turn the valve from “off” to the “filter” position. The tank needs to full of water and the unit will certainly begin filtering. Check once again for leaks. If you find leakages at the compression fittings or the filter real estate, tighten up until the dripping stops.
Step 6.
Modification the Filter as Needed.

You’ll need to change the cartridge at intervals suggested by the maker. When it come to the whole-house filter, the manage utilized to turn the inlet valve doubles as a device to get rid of the filter tank when it’s time to change filters.

Turn the valve handle to the “off” position.

Use the deal with to loosen up and get rid of the tank from the housing. Have a pail convenient to capture any water.

Pour the water from the tank and discard the old cartridge. Clean the within the tank with a clean fabric.

Place a brand-new cartridge and reattach the tank to the housing. Return the valve to the “filter” position.

Open one of the faucets slowly, and enable the water to run for a few seconds to enable trapped air to escape.

No Comments

Be the first to start a conversation

Leave a Reply

  • (will not be published)